Eco-Materials Processing and Design XV
Home > Science, Technology & Agriculture > Mechanical engineering and materials > Materials science > Eco-Materials Processing and Design XV
Eco-Materials Processing and Design XV

Eco-Materials Processing and Design XV

|
     0     
5
4
3
2
1




Out of Stock


Notify me when this book is in stock
About the Book

Collection of selected, peer reviewed papers from the 15th International Symposium on Eco-Materials Processing and Design, (ISEPD), January 12-15, 2014, Hanoi, Vietnam. The 74 papers are grouped as follows: I. Materials for Environment Preservation, Energy Conservation/Harvesting and New Energy, II. Materials Cutting and Processing Technologies for Reduction of Environmental Impact, III. Eco-Processing and Design on Polymer, Ceramics, Metals, Semiconductors, IV. High Performance Materials Including Nano-Materials for the Environment, and Coating/Corrosion, V. Hybrid Materials and Composites for ECO Society, VI. Photocatalysis for a Better Environment and Clean Energy, VII. Bio-Inspired Materials for a Better Life and Other Novel Bio-Materials, VIII. Light Metals and Alloys of Mg, Al, Ti, Be, and Porous Materials, IX. Steel and Alloy, X. Manufacturing and Mechanical Technology

Table of Contents:
Preface and Organizing Committee I. Materials for Environment Preservation, Energy Conservation/Harvesting and New Energy Characterization of Cast Iron Scrap Chips toward β-FeSi2 Thermoelectric Materials Two-Step Sintering of Non-Stoichiometric CeO2-x Adsorption Characteristics of Impregnated Adsorbent for Mercury Removal Effect of the Alkali-Activation on the Mechanical Property of Geopolymer Composite Fabrication of FRP Spacers of Insulating Glass for Energy-Saving Eco-Friendly Home Synthesis of Diglycerol Ester as Insulating Oil for Offshore Wind Turbine Transformer The Effects of Deposited Material and Loaded Amount within Synthesis of TMP-Ester Effect of CaO Content on Yb: YAG Disk Laser Weldability of AZ31 Mg Alloy Fabrication and Electrochemical Performance of Nitrogen-Doped Graphene Synthesized by Hydrothermal Method Graphene Oxide Based Selective VOCs Sensor for Indoor Air Quality Monitoring Thermocatalytic Degradation of Low Density Polyethylene Films at Artificial Aging Treatment under Lower Temperature Low-Temperature Thermocatalytic Degradation of Polyethene Films by Nano-Titanium Dioxide in Water Study on Aqueous Viscosity Behaviors of Hydroxypropyl Methylcellulose Hydrosol and Konjac Glucomanan Hydrosol Effect of Lignin and RLDPE Soil Amendments on Water Holding Capacities of Desert Biosorption of Strontium Ions by Low-Cost Sunflower Stem and Leaf Preparation and Characterizations of Novel Near Room-Temperature Driven Fe/Sr2Bi2O5 Thermocatalyst Effects of Ultrafine Grinded Steel Slag Addition on Properties of Cement Effect of Calcium Compounds on Mechanical Properties of Eco-Friendly Non-Cement Mortar Enhancement of PEM Fuel Cell Performance by Flow Control II. Materials Cutting and Processing Technologies for Reduction of Environmental Impact A Comparative Study on the Physical Properties of Artificial Aggregates Made from Acid Clay and Dredged Soil Dust Removal Using Electrode-Plates Coated with Activated Carbon Effects of Nano-Porous Materials and Inert Gas on Sound Proof Properties of Double Layer Acryl Plate Characteristics of MSWI Ash and its Application to Zeolite Synthesis III. Eco-Processing and Design on Polymer, Ceramics, Metals, Semiconductors Characteristics of Pollutants Removal by Carbonized Porous Media Made from Sewage Sludge Fabrication of Aluminum Superhydrophobic Surface with Facile Chemical Etching Method Purification and Size Control of AlN Powder for AlN Single Crystal Growth A Brief Review on TiO2 Coating Deposited by Cold Spraying Protective Agent Free Eco-Synthesis of Silver Nanowire via Needle-Shaped Silver Acetate Precursor Synthesis and Characterization of Ag/Graphene Nanocomposites by Solid-Liquid Sonochemical Reactions Production and Characterization of Recycled SUS 439L Powders by Gas Atomization Process Study on Recycling of Electric Arc Furnace Dust Preparation of Drug Loaded Polyurethane Thin Layer on the Silicone Tube by Electrospinning Technique for Stent Application A Smart System Combining Rainwater and Treated Sewage for Use in Sports Complexes in Korea Composition and Microstructure of Koryo Celadon in Korea IV. High Performance Materials Including Nano-Materials for the Environment, and Coating/Corrosion Density Functional Theory Study of the Interaction of Nitric Oxide with 3D Transition Metal Dimers Effect of Carbon Pre-Treatment on Pd Dispersion in Synthesis of Pd/C Catalyst Temperature Dependence of Magnetic Properties in Ferrite Powders by High Energy Ball Milling Self-Cleaning TiO2/SiO2 Thin Film Prepared by a Simple Sol-Gel Method Development of a Carbon Nanotube Paste for the High-Performance Field Emitters by Using the Simple Ball-Milling Method Application of Low Voltage in Quantitative Analysis by Energy Dispersive Spectrum (EDS) Surface Modification of CaCO3 Micro/Nanofillers by Pimelic Acid: Consequences on Crystallization Behaviors of Polypropylene Composites Synthesis and Characterization of Cu–TiC Nanocomposites by Ball Milling and Spark Plasma Sintering V. Hybrid Materials and Composites for ECO Society Crack-Healing Function of Nano-Ni/(ZrO2+Al2O3) Hybrid Materials Fabrication and Fracture Characteristics of AlN/Ni Laminated Composites Preparation and Thermal-Physical Properties of Three Dimensional Bicontinuous SiC/Cu-Si Composite Study on Electrical and Thermal Properties of Epoxy Resin/Inorganic Filler Composites for the Fully Enclosed Casting Bus Bar and its Calculation of the Temperature Field Preparation of Titanium Coating on Alumina Foam by Chemical Vapor Deposition Fabrication and Characterization of Silica Aerogel @Polystyrene Composite Beads by Suspension Polymerization Research on Preparation Technology for Machinable Ceramics VI. Photocatalysis for a Better Environment and Clean Energy The Photocatalytic Degradation of Methomyl over TiO2 Nanopowder Prepared by the Low Temperature Solvothermal Route Estimation of UV Dose for the Effective Degradation of Pharmaceuticals in Secondary Treated Wastewater Preparation of Fe/N Co-Doped TiO2 Powders by Mild Hydrothermal Method Control of Indoor Suspended Microorganisms by UV and Photocatalytic Disinfection Catalytic Activities of α, β, γ - Bismuth Molybdates for Selective Oxidation of Propylene to Arcrolein VII. Bio-Inspired Materials for a Better Life and Other Novel Bio-Materials Antibacterial Properties Evaluation of a Novel Polyurethane-Based Root Canal Sealer Potential of Tourmaline/Chitosan Fiber for Wound Dressing Fluoridation and Mechanical Properties of Hydroxyapatite with Addition of TiF3, Al2O3 and Fe2O3 by Sintering Application of Finite Element Method to the Simulation of Vessel Stents Influencing Factors on Chest Compression in Moving Ambulance Eating Speed Controls the Metabolic Syndrome VIII. Light Metals and Alloys of Mg, Al, Ti, Be, and Porous Materials Fractal Research of Pore-Structure in Porous Titanium Fibers Structure and Mechanical Properties of Lotus-Type Porous Copper with a Ti Coating on the Pore Wall by Arc Ion Plating Fabrication of Porous SiAlON Using Fe2O3 as Pore Former Thermal Stability of Amorphous Al-Fe-Y Prepared by Mechanical Alloying IX. Steel and Alloy The Study on Welding HAZ Microstructure of SAF 2507 Duplex Stainless Steel by Simulation Tests Phase Transformation Behavior of Niobium Containing Microalloyed Steel with Predeformation and Continuous Cooling Influence of Top Slag on the Plasticity of CaO-SiO2-Al2O3 Inclusions in 42CrMoA Crankshaft Steel Study on Microstructure and Fracture Morphology of 2205 Duplex Stainless Steel Resistance Spot Welds Effect of C Content on the Microstructure and Physical Properties of Fe-36Ni Invar Alloy Effects of Chromium Content and Impact Load on Microstructures and Properties of High Manganese Steel X. Manufacturing and Mechanical Technology Characterization of High Speed Steel Billets Fabricated by Electro-Slag Rapid Remelting Method Cutting Analysis of 3-Layer Laminated Plate Finite Element Simulation and Experimental Study on Internal Fracture of Railway Sleeper Screw during Cross Wedge Rolling Process Simulation Analysis of HPDC Process with Automobile Part by CAE


Best Sellers


Product Details
  • ISBN-13: 9783038352389
  • Publisher: Trans Tech Publications Ltd
  • Publisher Imprint: Trans Tech Publications Ltd
  • Height: 240 mm
  • No of Pages: 346
  • Weight: 800 gr
  • ISBN-10: 3038352381
  • Publisher Date: 12 Jan 2015
  • Binding: Paperback
  • Language: English
  • Spine Width: 17 mm
  • Width: 170 mm


Similar Products

Add Photo
Add Photo

Customer Reviews

REVIEWS      0     
Click Here To Be The First to Review this Product
Eco-Materials Processing and Design XV
Trans Tech Publications Ltd -
Eco-Materials Processing and Design XV
Writing guidlines
We want to publish your review, so please:
  • keep your review on the product. Review's that defame author's character will be rejected.
  • Keep your review focused on the product.
  • Avoid writing about customer service. contact us instead if you have issue requiring immediate attention.
  • Refrain from mentioning competitors or the specific price you paid for the product.
  • Do not include any personally identifiable information, such as full names.

Eco-Materials Processing and Design XV

Required fields are marked with *

Review Title*
Review
    Add Photo Add up to 6 photos
    Would you recommend this product to a friend?
    Tag this Book Read more
    Does your review contain spoilers?
    What type of reader best describes you?
    I agree to the terms & conditions
    You may receive emails regarding this submission. Any emails will include the ability to opt-out of future communications.

    CUSTOMER RATINGS AND REVIEWS AND QUESTIONS AND ANSWERS TERMS OF USE

    These Terms of Use govern your conduct associated with the Customer Ratings and Reviews and/or Questions and Answers service offered by Bookswagon (the "CRR Service").


    By submitting any content to Bookswagon, you guarantee that:
    • You are the sole author and owner of the intellectual property rights in the content;
    • All "moral rights" that you may have in such content have been voluntarily waived by you;
    • All content that you post is accurate;
    • You are at least 13 years old;
    • Use of the content you supply does not violate these Terms of Use and will not cause injury to any person or entity.
    You further agree that you may not submit any content:
    • That is known by you to be false, inaccurate or misleading;
    • That infringes any third party's copyright, patent, trademark, trade secret or other proprietary rights or rights of publicity or privacy;
    • That violates any law, statute, ordinance or regulation (including, but not limited to, those governing, consumer protection, unfair competition, anti-discrimination or false advertising);
    • That is, or may reasonably be considered to be, defamatory, libelous, hateful, racially or religiously biased or offensive, unlawfully threatening or unlawfully harassing to any individual, partnership or corporation;
    • For which you were compensated or granted any consideration by any unapproved third party;
    • That includes any information that references other websites, addresses, email addresses, contact information or phone numbers;
    • That contains any computer viruses, worms or other potentially damaging computer programs or files.
    You agree to indemnify and hold Bookswagon (and its officers, directors, agents, subsidiaries, joint ventures, employees and third-party service providers, including but not limited to Bazaarvoice, Inc.), harmless from all claims, demands, and damages (actual and consequential) of every kind and nature, known and unknown including reasonable attorneys' fees, arising out of a breach of your representations and warranties set forth above, or your violation of any law or the rights of a third party.


    For any content that you submit, you grant Bookswagon a perpetual, irrevocable, royalty-free, transferable right and license to use, copy, modify, delete in its entirety, adapt, publish, translate, create derivative works from and/or sell, transfer, and/or distribute such content and/or incorporate such content into any form, medium or technology throughout the world without compensation to you. Additionally,  Bookswagon may transfer or share any personal information that you submit with its third-party service providers, including but not limited to Bazaarvoice, Inc. in accordance with  Privacy Policy


    All content that you submit may be used at Bookswagon's sole discretion. Bookswagon reserves the right to change, condense, withhold publication, remove or delete any content on Bookswagon's website that Bookswagon deems, in its sole discretion, to violate the content guidelines or any other provision of these Terms of Use.  Bookswagon does not guarantee that you will have any recourse through Bookswagon to edit or delete any content you have submitted. Ratings and written comments are generally posted within two to four business days. However, Bookswagon reserves the right to remove or to refuse to post any submission to the extent authorized by law. You acknowledge that you, not Bookswagon, are responsible for the contents of your submission. None of the content that you submit shall be subject to any obligation of confidence on the part of Bookswagon, its agents, subsidiaries, affiliates, partners or third party service providers (including but not limited to Bazaarvoice, Inc.)and their respective directors, officers and employees.

    Accept

    New Arrivals

    Inspired by your browsing history


    Your review has been submitted!

    You've already reviewed this product!