Performance Based Building Design 2: From Timber-framed Construction to Partition Walls

Just like building physics, performance based building design was hardly an issue before the energy crises of the 1970ies. With the need to upgrade energy efficiency, the interest in overall building performance grew. The term "performance" encompasses all building-related physical properties and qualities that are predictable during the design stage and controllable during and after construction. The term "predictable" demands calculation tools and physical models that allow evaluating a design, whereas "controllable" presumes the existence of measuring methods available on site. The basis for a system of performance arrays are the functional demands, the needs for accessibility, safety, well-being, durability, energy efficiency and sustainability and the requirements imposed by the usage of a building. In continuation of Vol. 1 this second volume discusses light-weight construction with wooden and metal elements, roofing systems, facades, and ends with finishes and the overall risk analysis. Most chapters build on a same scheme: overview, overall performance evaluation, design and construction. The work is absolutely recommended to undergraduates and graduates in architectural and building engineering, though also building engineers, who want to refresh their knowledge, may benefit. The level of discussion assumes the reader has a sound knowledge of building physics, along with a background in structural engineering, building materials and building construction. Where and when needed, input and literature from over the world was used, reason why each chapter ends listing references and literature.

Table of Contents:
Preface 1. Timber-framed construction In general Performance Evaluation Design and Execution 2. Sheet-metal Outer Wall Systems In general Performance Evaluation Design and Execution 3. New Developments Transparent Insulation Multiple Skin and Photovoltaic Outer Walls 4. Roofs: Requirements In general Performance Evaluation 5. Low-sloped Roofs Typologies Roofing Membranes Compact Low-sloped Roofs Protected Membrane Roofs 6. Pitched Roofs Classification Roof Covers in detail Basic Assemblies Performance Evaluation Design and Execution 7. Sheet-metal Roofs In general Metal Roof Cover Performance Evaluation Design and Execution 8. Windows, Outer Doors and Glass Facades In general Glass Windows and Doors Glass Facades 9. Balconies, Chimneys, Shafts and Stairs In general Balconies Shafts Chimneys Stairs 10. Partitions; Wall, Floor and Ceiling Finishes; Inside Carpentry In general Partition Walls Building Services Wall Finishes Floor Finishes Ceiling Finishes Inside Carpentry 11. Risk analysis In general Risk Definition Performing a Risk Analysis Example of Risk Analysis: Cavity Walls

About the Author :
Prof. Em. Dr. Ir. Hugo S.L.C. Hens, University of Leuven (K.U. Louvain, Belgium), taught Building Physics from 1975 to 2003, Performance Based Building Design from 1970 to 2005 and Building Services from 1975 to 1977 and 1990 to 2008. Until 1972, he worked as a structural engineer at a mid-sized architectural company, constructing houses, apartment buildings and office buildings. He has authored and co-authored over 150 articles and conference papers, and written hundreds of reports on building damage cases and their solution. He has been coordinating the international working group CIB W40 on Heat and Mass Transfer in Buildings for ten years. Between 1986 and 2008, he was operating agent of four Annexes, initiated by the International Energy Agency?s EXCO on Energy Conservation in Buildings and Community Systems: Annex 14, Annex 24, Annex 32 and Annex 41. He is also a fellow of the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE). Prof. em. Dr.-Ing. Hugo S. L. C. Hens, Universität Leuven (K.U. Leuven/Belgien) lehrte Bauphysik von 1975 bis 2003, Gebäudeplanung von 1970 bis 2005 und Technische Gebäudeausrüstung von 1975 bis 1977 sowie von 1990 bis 2008. Bis 1972 war er als Tragwerksplaner für Wohnhäuser, Büro- und Geschossbauten in einem Architekturbüro tätig. Er hat als Autor bzw. Koautor über 150 Artikel und Tagungsbeiträge veröffentlicht und hunderte Schadensgutachten erstellt. Während zehn Jahren koordinierte er die internationale Arbeitsgruppe CIB W40 "Heat and Mass Transfer in Buildings". Von 1986 bis 2008 war er im Rahmen des Forschungsprogramms "Energy Conservation in Buildings and Community Systems" der Internationalen Energieagentur IEA für die Erarbeitung von Annex 14, Annex 24, Annex 32 und Annex 41 verantwortlich. Er ist Mitglied der American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE).