New Materials and Technologies in Mechanical Engineering: (Volume 822 Key Engineering Materials)

This volume contains papers which were presented on the International Scientific Conference "New Materials and Technologies in Mechanical Engineering" (NMTME 2019, March 12 - 15, 2019, St. Petersburg, Russian Federation) and reflects the current level of development of materials science and technologies of materials processing in the modern mechanical engineering production. We hope this collection will be useful for many specialists in the field of mechanical engineering.

Table of Contents:
Preface Chapter 1: Metallurgical Technologies, Properties of Steels and Alloys Structure Diagnostic of Iron-Based Out-of-Peritectic Alloys during Nonequilibrium Crystallization The End-to-End Simulation of Semi-Continuous Casting and Subsequent Hot Rolling with Account of Microstructure Research of the Causes of the Defect "Sliver" on the Inner Surface of the Steel Pipe Strength Category Х70 Filtration Permeability of Dendritic Structure in Condition of Diffusion-Capillary Coalescence of Secondary Side Branches Phosphorus Removal Options at Induction Melting of Steel Modification of Nitrogen-Containing High-Chromium Steels by Nanosized Lanthanum Hexaboride Formulas for the Calculation of Temperatures and Concentrations of Carbon Responsible to the Parar Equilibrium of the Main Phases in Medium Sheet Steels Homogenization of Cr-Ni Austenitic Steel Studying: Liquation and Microhardness Heterogeneity Equalization Cast Austenitic Steels for Cryogenic Technology Numerical Simulation of Hot High Strain Rate Torsion Tests for Al-Based Alloys General Experimental Method of Research of Anisotropy of Conductive Materials Effect of Microstructure and Impact Toughness, on the Character of the Destruction of Main Oil and Gas Pipelines Application of Innovational Sc-Containing Alloys in Shipbuilding Effect of Severe Plastic Deformation on the Structure and Properties of the Aluminum Alloy System Al-Cu-Mg Improving the Properties of Aluminum Alloy System Al-Cu-Mg, Subjected to Hardening and Severe Plastic Deformation Joining of Titanium and its Alloys with Aluminum Alloys by Friction Stir Welding The Obtaining Layered Composite Materials that Contain Rare Earth Element Temperature Influence on Microstructure and Properties Evolution of Friction Stir Welded Al-Mg-Si Alloy Comparison of Porosity Evaluation Methods Using the Example of Dissimilar Metal Joints Chapter 2: Technologies of Plastic Processing of Materials The Method for Determining the Friction Coefficient in Relation to the Hot Forging Processes Improving the Quality of Parts Produced by Bending in a Die with an Elastic Element Investigation of the Hammer Forging Process of Large-Sized Turbine Blades of Stainless Steel Hot Axial Rotary Forging of Flanges Standard EN 1092 Researching Conditions of Thermomechanical Process under Semihot Forging Influence of Contact Friction on the Kinematics of Metal Flow during Equal Channel Angular Pressing Determination of Boundary Parameters of Pipelines Elbows Blanking Elements Made from Titanium Alloy Ti-4Al-2Mn and Steel AISI 304 Mechanical Properties of Bars Produced by Hot Extrusion of Magnesium Shavings Chapter 3: Composites and Polymers, Intermetallic Compounds and Powder Materials Manufacturing and Properties of Radiation Resistance Aluminum Alloys and Composites with Addition of Gadolinium Effect of Nanocarbons Additions on the Microstructures and Properties of Copper Matrix Composite by Spray Drying Process Investigation and Characterization of New Polyimide Powder for Selective Laser Sintering Friction and Wear Characteristics of UD Thermoplastic Tape Based Nanocomposites with Fullerene Soot Investigation by TGA, DSC and DMA Urethane-Imide Copolymers with High Content of Hard Imide Blocks Si Nanopowder Based Anode Material for the Lithium Ion Battery Cell Research of the Possibility of Obtaining a Foam System of Aluminum - Carbon Nanotubes Using a High-Temperature Foam Agent Effect of High Energy Ball Milling Washing Process on Properties of Nd2Fe14B Particles Obtained by Reduction-Diffusion The Technology of Producing Layered Composite Materials on the Basis of Hypoeutectic Silumin AK9ch and Sintered Iron Powder AHC100.29 Consolidation Behavior of the Cu-Al2O3 Nanocomposite Powder General Method of Research of Electrophysical Properties of Nanostructured Composites Obtaining a Hard Alloy Powder from a Worn-Out Tools with a Subsequent Use for Pressing Rods Comparison of Supermacroporous Polyester Matrices Fabricated by Thermally Induced Phase Separation and 3D Printing Techniques The Research and Development of the Technology for Pressure Treatment of the Thermally Expanded Graphite Powders Correlation of Nonuniformities of the Seebeck Coefficient’s Distribution and the Strain-Stress State in Extruded Thermoelectric Material Nanostructural Composites in the WC/ZrO2 (Y2O3) System Obtaining Spherical Powders of Grade 5 Alloy for Application in Selective Laser Melting Technology Synthesis of the In Situ Nb-Si Composites by Binder Jetting Additive Manufacturing Technology Aerosol-Assisted Chemical Deposition of Nanocomposite Material in the "Iron-Carbon-Oxygen" System Research of Regularities of Aerosol Synthesis of Iron Oxide Particles Synthesis and Study of Nanocrystalline Mg2SiO4 Powder and Yttrium Aluminum Garnet Agricultural By-Products as Advanced Raw Materials for Obtaining Modifiers and Fillers for Epoxy Materials Wood - Polymer Composites Assessment Using Microtomography Effect of Processing and Radiation Exposure on the Structure and Properties of Polypropylene Investigation of Composite Materials Impact Damage by a Computer Tomography Chapter 4: Laser Technologies and Additive Manufacturing Influence of Powder Condition on Surface Properties of Cold-Resistant High-Strength Steel Produced by Direct Laser Deposition Method Аpplication Development for the Evaluation of Penetration in Laser and Laser-Arc Hybrid Welding of Tee and Corner Joints Phase and Structural Transformations in Heat Resistant Alloys during Direct Laser Deposition Measurement of Thermal Cycle at Multi-Pass Layer Build-Up with Different Travel Path Strategies during DLMD Process Research of Effect of the Powder Material Quality in the Structure Formation of the DLD Inconel 718 Samples Effect of Process Parameters on Microstructure and Mechanical Properties of Direct Laser Deposited Cold-Resistant Steel 09CrNi2MoCu for Arctic Application Research of Mechanical Properties of Cold Resistant Steel 09CrNi2MoCu after Direct Laser Deposition Analysis of the Source Type Influence on the Structure Forming during Aluminum Wire-Feed Laser Deposition An Analytical Model for Filler Wire Heating and Melting during Wire Feed Laser Deposition Modeling of the Formation Process of the Coherent Intermetallides in Nickel Alloys during Laser Treatment Effect of Inter-Layer Dwell Time on Distortion and Residual Stresses of Laser Metal Deposited Wall Current Design Rules for Welding of Wind Energy Structures for Arctic Conditions Feasibility Study of Hybrid Laser Arc Welding Application in Shipbuilding Structure and Phase Composition of Ti-6Al-4V Samples Produced by Direct Laser Deposition Comparison of Titanium Powders and Products Manufactured by the Direct Laser Deposition Method Investigation of Crystallization Process of a Single Crystal Nickel-Based Alloy during the Laser Multilayer Cladding Manufacture of a High-Pressure Centrifugal Fan Made of 316l by the Method of High-Speed Direct Laser Deposition Research of the Treatment Parameters Effects on the Layer Formation during Wire-Feed Laser-TIG Deposition with Aluminum Alloy Research of the Structure Defects at Wire-Feed Laser and Laser-Arc Deposition with AlMg6 Features of Laser Welding Light Constructions from Cryogenic Austenitic Steel 316L Laser Cladding of Heat-Resistant Iron Based Alloy Designing of Topology Optimized Parts for Additive Manufacturing Investigation of Aluminum Composite Produced by Laser-Assisted Cold Spray Additive Manufacturing X-Ray CT Investigation of Graded Ti-Ti64 Material Produced by Selective Laser Melting Effect of Selective Laser Melting Process Parameters and Heat Treatment on Microstructure and Properties of Titanium Alloys Produced from Elemental Powders The Effect of Laser Power on the Microstructure of the Nb-Si Based In Situ Composite, Fabricated by Laser Metal Deposition Investigation of Functional Graded Steel Parts Produced by Selective Laser Melting Evolution of the Lattice Structures Properties Manufactured by Selective Laser Melting and Subsequent Hot Isostatic Pressing Selective Laser Melting of Nanocomposite Ti-6Al-4V and TiC Powder Control of Deviations in Lattice Structures Manufactured by Selective Laser Melting Chapter 5: Applied Plasma Technologies Registration of an ICP Plasma CV Dependences under Various Pressures in the Plasma-Chemical Deep Etching System Calculating the Nominal Values of the Matching Device Installation of Plasma Chemical Etching Microstructure and Mechanical Properties of Powder Steel 16Cr - 2Ni - Mn - Mo Obtained by Mechanical Alloying and Spark Plasma Sintering Design of Special Device for the Forced Electrolytic-Plasma Polishing of Internal Surfaces by Counter Flows Effect of the Mechanical Alloying and Spark Plasma Sintering on Microstructure, Phase Composition and Chemical Elements Distribution of Nb-Si Based Composite Plasma Chemical Synthesis of Aluminum Nitride Nanopowder Technological Principles of Internal Surfaces Finishing by Forced Electrolytic-Plasma Polishing Aspect-Independent Siliconglass Etching by Bosch Method Chapter 6: Engineering Tribology, Coatings and Surfaces in the Design of Machine Parts and Mechanisms Tribotechnical Diagnostics of an Internal Combustion Engine According to the Condition of the Oil Investigation of Tribological Characteristics of Polymers Used in Medicine Vibroacoustic Study of Abrasive Wear of Multilayered Sliding Bearings Comparative Tribological Testing of Diamond-Containing Inserts of Bearings of Main Shaft of Rotary Steerable Systems Formation of Nanostructure and Tool Wear during Cutting Treatment of Titanium Alloy Study of Micro-Hardness of Steel Surfaces after their Friction in the Medium of Plastic Lubricating Material Used in the Units and Mechanisms of Equipment of Oil and Gas and Shipbuilding Industry Method of Testing Rolled Tubular Products for Oilfield Pipes for Corrosion-Abrasive Wear Evaluation of the Strength of Flat Gears According to the Criterion of the Onset of Plastic Deformation Semiempirical Mathematical Models of Spinning Friction Steel ShKh15 Steel Titles on Steel R6M5, on a Scheme of a Globe Plane Taking into Account Wear Studies of Tribological and Corrosion Properties of Coatings Based on Iron for Light Alloy Drill Pipes of Aluminium Alloys Strain and Friction Effect on the Stress-Strain State in the Deformation Zone during Cold Rolling of Thin Beryllium and Aluminum Foils Quasi-Optimal Correlation Algorithm for Measuring the Parameters of Surface Microrelief Method for Determining Texture Parameters of Processed Precision Surfaces by Correlation Finite Element Simulation of Temperature Field during Friction Surfacing of Al-5Mg Consumable Rod Improvement of Technology of Formation of Coatings with Metal Effect by Modified Water-Dispersion Paints Corrosion-Resistant Ceramic Coatings that are Promising for Use in Liquid Metal Environments Study of the Method of Obtaining Functional Interest-Metallic Coatings Based on Ni-Ti Reinforced with WC Nanoparticles Technological Aspects of Obtaining Functional Gradient Coatings to Protect Machinery from Wear Technological Aspects of Obtaining Functional Coatings Based on Silver by the Method of Cold Gas-Dynamic Spraying Electrochromic Properties of NiO Thin Coatings The Use of the TMA as Stabilizing Reagent for the Li-O System Obtained by Atomic Layer Deposition Features of the Implementation of the Vegard’s Law in Thin Films of Rare Earth Elements Compounds Effects of PTA Deposition Parameters on Coating Quality of 41Cr4, 50CrV4 and 100Cr6 Steel Chapter 7: Amorphous Materials with Special Properties Influence of Se on Properties of As-S-Se-I Glass for Immersion Mid-IR Leds Lenses Ionic Seebeck Effect in Alkali Niobophosphate Glasses Structural Features and the Effect of Two Alkalis in Chalcogenide and Phosphate Glasses Fusible Glass Based on Glassy Chalcogenide Type Systems Ge-S(Se)Br, Ge-S(Se)I Bi-Activated Glasses and their Potential Covering Spectral Region as Active Media for Tunable near Infrared Lasers Effective Diagnostics of Internal Defects of Diamonds in the near Infrared Range on the Basis of Immersion Medium Made from Low-Melting Chalcogenide Glass Formation of New Glass-Ceramic Materials with Controllable Dielectric and Magnetic Properties Electronic Structure and Ionic Transport in Phosphate Glass with Pyrophosphate Structural Elements Manifestation of Сoncentration Quenching of Fluoroaluminate Glasses Doped with Erbium Study of Crystallization Kinetics of Amorphous Zirconia in Fe2O3 Matrix by Kissinger Method Investigation of the Pastes for Multilayer Ceramic Capacitors Termination